免费人成在线视频

<rp id="agjvg"><object id="agjvg"><blockquote id="agjvg"></blockquote></object></rp>

    <th id="agjvg"></th>

    歡迎訪問溫州市旭日印刷機械有限公司官網!

    搜索
    您當前所在位置:網站首頁 > 新聞中心 > 行業新聞
    溫州市旭日印刷機械有限公司前身是溫州市南方包裝機械廠,坐落在溫州梧埏工業基地,距火車站僅2公里,交通便捷
    PJQ-100型切角機維護保養

    發布時間:2019-10-31

    瀏覽次數:192

      為了延長機器的使用壽命,保證機器能順利工作,正確地維護、保養機器是至關重要的。

      1操作者應定期檢查機器的各部件是否正常,各油孔是否有堵塞現象,并應及時排除故障。

      2應于各銅套、活動面經常加注潤滑油,使機器保持良好的潤滑狀態。

      3切刀要保持鋒利,用鈍刀裁切即要縮短機器的使用壽命又不能裁出理想的成品。

      4工作臺上不要放扳手、螺絲刀等硬物,要經常擦拭機器使機器保持清潔、干凈。

      The distribution of lubrication points is shown in Figure 3.

      In order to extend the service life of the machine and ensure that the machine can work smoothly, it is crucial to properly maintain and maintain the machine.

      4.1 The operator shall regularly check the regularity of the parts of the machine and the blockage of the oil holes and shall promptly troubleshoot them.

      4.2 The copper sleeves and movement surfaces shall be lubricated regularly to maintain the machine in good lubrication condition.

      4.3 To keep sharp, cutting with a blunt knife reduces the service life of the machine and does not produce the desired finished product.

      4.4 Do not put a wrench, screwdriver and other hard things on the platform. Always wipe the machine to keep it clean.

      Δ注意事項:

      1.必須在停機狀態下調整機臺。

      2.工作時,手遠離切刀。

      3.機臺的軸,每月加注潤滑油一次

      4.非本機操作人員禁止操作本機。

      ΔNotes:

      1. Must adjust the platform under downtime.

      2. Keep your hands away from the cutter while working.

      3. The shaft of the platform is lubricated once a month

      4. Non-native operators are prohibited from operating this machine.

      圖(3)傳動原理示意圖

      Figure(3) A schematic diagram of transmission principle

    潤滑點

     Lubrication point

    推薦潤滑油 

    Recommended lubricants

    加油次數 

    Number of refuels

    備注 

    Remarks

    1

    40#機油 

    Engine oil

    每天一次 

    Once a day.

    拖板活動面 

    Drag board active surface

    2

    40#機油 

    Engine oil

    每天一次 

    Once a day.

    連桿下關節 

    Sublink joint

    3

    40#機油 

    Engine oil

    每天一次 

    Once a day.

    連桿上關節 

    Connecting rod upper joint

    4

    40#機油

     Engine oil

    每天一次 

    Once a day.

    偏心輪軸孔 

    Eccentric shaft hole

    5

    40#機油 

    Engine oil

    每天一次 

    Once a day.

    開關座活動面 

    Switch seat active surface

    6

    40#機油 

    Engine oil

    每天一次 

    Once a day.

    飛輪軸孔 

    Flywheel shaft hole

    新聞詳情
    免费人成在线视频

    <rp id="agjvg"><object id="agjvg"><blockquote id="agjvg"></blockquote></object></rp>

      <th id="agjvg"></th>